Mesas or Rocky Outcrops from Diabolical Terrain

    A collection of 3-D printed rocky outcrops or mesas that I purchased from Diabolical Terrain

Last year, knowing that Star Wars skirmishes I am running using Space Weirdos rules were in the future for our gaming, I picked up a set of mesas or rocky outcrops from Diabolical Terrain. These are 3-D printed and in a nice variety of sizes from their Desert Rock Formations collection. In fact, I would say that these would work easily for just about any scale. I have them posed with my 28mm 3-D printed Stormtroopers from JS Wargamer Printing, but I could easily see these prints being equally perfect for 15mm. It just depends on how big you want your rocky outcrops or mesa terrain to be!

    28mm Star Wars Stormtroopers search through the canyonland of Tatooine for 'rebel scum'

The first step to preparing these for the tabletop was to spray paint them with a can of khaki "camouflage"  paint that I picked up at Menards. It's the same base coat I used for my Diabolical Terrain Tatooine houses that I painted up back in December. Like with those buildings, I will likely pick up more of these mesas when I see Ron Weaver at his booth at Historicon. I purchased these rocky outcrops from him at last Historicon. They seemed like plenty of pieces for a nice desert tabletop. However, once I got them finished and set out on my desert terrain neoprene mat, they didn't cover up as much of it as I thought they would! 

    'Any signs of the rebels, Echo Six?' 'No, sir.' 'Keep looking -- Lord Vader says they're here...' 

Once the spray painting was done, I was able to skip my usual next step of applying watered down acrylic paint to make sure it gets in all the cracks and crevices. This spray did a thorough job of it, and after inspecting the pieces closely, I decided to go straight to dry brushing. I applied a dry brush of a craft paint called "Wild Rice" -- a very light colored tan that I typically use for highlighting khaki. This brought out the carved rock faces well.

    The 3-D printed pieces were easy to paint up and prepare for the tabletop in four steps

As much as I liked it, I feel a wash always does a great job "softening" and blending in the brush strokes of the highlighting step. There was a lot of surface area, though. Did I want to use my standard brown vehicle wash, which is fairly dark, as well? Hmmm. Then I remembered what project I bought the spray paint I'd used on them for -- my giant, 3-D printed bridge. I had mixed up a special batch of wash just for that bridge, knowing it would take a lot of liquid to cover its surface. I still had what was left over sitting, pre-mixed, on my tabletop. I would look at it from time to time, and shake it to ensure it hadn't dried up. Would it be enough, though? I figured that I would try it first on one of the smaller pieces.

    I really like how the different shades of brown I used on the various steps amplify the shadows

I really liked the effect it gave. Sometimes, if the wash is too dark, it almost erases the previous highlighting. This was a nice in between. You could see the lighter highlights, but it did a nice job of blending the brush strokes and giving a nice, brown color. I went ahead and finished the rest of the pieces and still have some more left over. So, it had definitely been plenty! Once dry, I inspected the pieces. I liked them, but felt that the recesses and cracks were still too light. Hmmm.

I decided to do one final step on the pieces. I took my dark brown vehicle wash and applied it with a small brush only to the cracks and crevices. Although in a few places you can see where this stops and starts too clearly, in my opinion, I was overall happy with how it turned out. I think on my next batch, though, I will swap the last two steps. I will do the brown vehicle wash in the crevices and recesses and then do the overall wash on it. I think it will blend the whole rocky surface together well. A final clear matte spray coat finished off the pieces.

    You can see how the size of these pieces would work for either 15mm or 28mm scale

You can see the 3-D print lines in some of the close up photos. However, since it is a sandstone like surface, this actually doesn't look bad. It gives the impression of even smaller details on the rock surfaces itself. I like how these turned out, and I said before, will likely be buying more of them from Diabolical Terrain. They will be used on the tabletop for sure in my next planned scenario in our Star Wars campaign using Space Weirdos rules.

    One final look at the rocky pieces from above to show you their variety in size and shape

So, what else is coming up or in progress? Lots! Too much!! Seriously, I will post tomorrow my next batch of 28mm Viet Cong. Posing with them will be my first dozen jungle scatter terrain pieces that I scratch built using plastic plants from the local craft store. I actually took the photos of those at the same time as these. I had finished the rocky outcrops first, though, so they get to be featured on the blog first! Fair is fair...ha, ha! Of course, there are more U.S. and Viet Cong figs in process. In addition, there are a LOT of terrain pieces that I am preparing for the sole purpose of selling at my flea market table at Historicon this July 17-20 in Lancaster, PA. Stay tuned for updates on those and other miscellaneous terrain or figures I am squeezing into my painting schedule.

MINIATURES Acquired vs. Painted Tally for 2025

• Miniatures acquired in 2025: 145
  
• Miniatures painted in 2025: 85 

TERRAIN Acquired vs. Painted Tally for 2025

• Terrain acquired in 2025: 21
  
• Terrain painted in 2025: 32

SCATTER Acquired vs. Painted Tally for 2025

• Scatter acquired in 2025: 93
  
• Scatter painted in 2025: 60