Merchant's Store for My Medieval City

    3-D printed medieval building from the Ferisia line from RRB Minis & More - Merchant Store B

After building another of the large buildings last month from the Ferisia line carried by RRB Minis & More, I decided to build a smaller one next. As opposed to the towering ones composed of 4-5 levels/roofs, Merchant Store B had only two pieces. The lower one was the house itself while the upper one was just the interesting looking roof. What I liked most about it was the covered patio attached to the house, where the merchant would ostensibly sell his goods. It was a unique design and matched the overall look of the buildings I've been painting up, so far. The STLs for the Ferisia line are from Dadi Dungeon & Dintorni. They've created a number of other, very interesting lines, and I highly recommend folks to check them out. 

    Side and rear of the merchant house, with a good look at the wooden tile roof

As much as I like the 3-4 story Duncan and Catrin Houses, I assume that most medieval cities would have a limited number of buildings that tall. The bulk of the homes would more likely be one or two stories tall. Because of that, I'd picked this building up from Rich Brown of RRB at Cincycon, and fast-tracked it to be the first one that I painted up. Of course, I bought another tall one at the same time, simply called the "Merchant's House," that is four stories tall (interestingly, the roof being part of the 4th story). Considering that I just came back from Little Wars 2026 yesterday, where I bought three more buildings from him, I have a feeling this is going to be a routine for this year. See Rich, buy buildings! Ha, ha!!

    My favorite part of this building is the roofed patio and its counter where the merchant sells products

Anyway, back to the Merchant Store B! I painted this one up using the same system as the others, with a black spray prime followed by a 50/50 mix of water and acrylic black paint. Once dry, I completed the stone sections first. I gave them a dark gray wet brush over the black, then a light gray dry brush. Next, I painted the wooden sections dark brown, followed by two highlights -- a medium Camo Brown from Howard Hues and a Khaki dry brush. Next, I painted up the metal components on the two doors and pillars holding up the open air, covered patio. I base coated them in Iron Wind Metals Steel first, followed by Bronze. I wet brushed the window panes and frames in Iron Wind Dun yellow.

    A look at the interior of Merchant Store B and its patterned wooden floor & fireplace

The results on the building looked good, but I thought it needed more. I decided to do a checkered pattern on the stone tile covered patio. I used a very light dry brush, alternating the colors of the square sections in Dun yellow and a light Wedgewood blue. I liked how that looked, so added those colors to the raised arc of stones surrounding the front door to the house and the side door from the patio to the home. Finally, I echoed those colors again on the rooftop's conical decorations. I had gone back and forth on whether to portray those finals as metallic or simply painted wood. In the end I went with painted wood in pastel blue and yellow.

    Front doorway with its 2 torches,  blue & yellow stone archway, & decorated wooden door

There are also two torches flanking the front entrance. Originally, I was worried they might be fragile, considering they are 3-D printed. However, I never brushed them accidentally during painting, so I think they'll be fine. The torches were completed with a wooden handle, metal rim, and very bright yellow and orange. I admit I am a bit worried about the conical decorations on the roof's spine. I snapped a couple off in transporting the building home from Cincycon, but luckily Rich had the foresight to include extras. This is a similar to a problem with the finials on the railings of the Catrine House. You really have to be careful where you put your hands on the model to pick it up. No "claw" grips! Watch where you clasp your fingers around it to pick it up! Otherwise, these 3-D printed buildings are sturdy and solid state. I have no worries about breaking off any other sections. As you can tell from how many I have bought, I really like this line of buildings and Rich does a great job on printing them.

    I wasn't sure how to paint the wooden tile (or 'Shake') roof -- decided to go with a new wood tone

The roof of Merchant Store B obviously looked to me like it had wooden tiles -- not terra cotta ones. I was tempted to paint it with the same red brown base coat and orange flesh dry brush anyway, but decided not to, instead.  I did a handful of Google searches on wooden or "shake" tile roofs. Based on those, I decided to do a different tone of brown. I wet brushed the tiles with a medium leather craft color called Raw Sienna. Next, I did a dry brush of craft paint of a darker Khaki color. I liked the different tone it gave from the wooden beams and patio pillars. In fact, I liked it so much that I chose not to do a black wash over it for fear it would "gray out" the colors too much. Same with the gray stone sections of the store. I did the black wash only on the wooden beam/pillars, the metal, and the Dun yellow windows. I really like how it came out!

    I did a blue and yellow patterned tile flooring to the patio, which comes off of the side of the house

So, what's next on my painting desk? I'm hurrying to get things together for my scenario that I will be running at Drums at the Rapids, May 15-16. I'll be using my medieval town terrain for it, and I want to get as many structures completed as possible. So, in that light, I'm painting up two of the smaller ones that I bought this past weekend from him at Little Wars (see them in an upcoming post on the convention). To go with that, I'm also working on a batch of eight figures that can pass for medieval townsfolk. You know how it goes -- if I am not rushing to get something completed it time for a game I'm running at a convention, things just aren't right! So, considering the upcoming deadline, hopefully you will see more updates soon!

    A final look at the newest addition to my medieval town, which will be used this weekend in a game!

MINIATURES Acquired vs. Painted Tally for 2026

• Miniatures acquired in 2026: 159
  
• Miniatures painted in 2026: 91

TERRAIN Acquired vs. Painted Tally for 2026

• Terrain acquired in 2026: 3
  
• Terrain painted in 2026: 23

SCATTER Acquired vs. Painted Tally for 2026

• Scatter acquired in 2026: 16
  
• Scatter painted in 2026: 56